ARRussell
2009-10-30T18:45:38Z
I intend to fit an autopilot and I'd like to know how they're usually fitted on the 235. There are various extension tubes and brackets available that might allow it to be mounted on the seat or the cockpit coaming, under the tiller or over the tiller. If the pin is fitted on top of the tiller, how is the tiller extension accommodated? Presumably an under-tiller bracket would foul the engine when raised? Any advice?

Anthony Russell

235/02 Sea Wyche


Anthony Russell

235/02 Sea Wyche

david boyle
2009-11-02T17:00:31Z
Hi Anthony

I fitted simrsd tp10.

Fitted on cockpit coaming,over the top with a 90mm push rod extension

and 90mm pedesstal bracket.

Be Be 235/49


Be Be 235/49
ARRussell
2009-11-05T21:38:04Z
Thanks David, that's useful. How did you overcome the tiller extension fouling the pin?

Anthony Russell

235/02 Sea Wyche


Anthony Russell

235/02 Sea Wyche

david boyle
2009-11-07T18:51:07Z

Anthony,

I put some packing under the tiller extension stowage clip,then the

push rod fits between the tiller extension and the tiller.

Hope this helps if not ill take some photos next time i go to boat.

Be Be 235/49


Be Be 235/49
david boyle
2009-11-08T09:17:24Z

Anthony

Just a thought

You may not need the 90mm pedestal bracket,because later 235 have a

longer rudder stock so the engine can be lifted out of the water.

Dave

Be Be 235/49


Be Be 235/49
Paul Bowman
2009-11-08T11:24:58Z
Anthony

I fitted the Raymarine ST1000 to my 235. I needed a 5" pushrod extension(Part no D007)that Bill Parker told me to buy.I drilled a hole in the bottom of the tiller extension to accomodate the pin that protrudes on top of the tiller. When the tillerpilot is attached, the extension is loose or it can be fastened down with shock-cord. It fastened straight onto the coaming without the need for any brackets, so the overall installation is clean and tidy. It took Peter (Zephyr) and myself about 2 hours to install fully. Hope this helps.

Paul

Paul

235/17 Kinkajou


Paul

Hunter Pilot 27, GiGi

(ex 235 owner)

ARRussell
2009-11-09T19:29:23Z
Thanks to both of you. That's all clear. I'm interested in the extended rudder stock, which I've read about before, because I would like to be able to lift the engine clear of the water while sailing - I can currently only sit it on the cavitation plate, so I can't fit the hull plug. I might modify my rudder stock later or, perhaps, get a curved tiller made. It's good to know the necessary pedestal is available for the autopilot to accommodate that modification.

Anthony Russell

235/02 Sea Wyche


Anthony Russell

235/02 Sea Wyche

Bob
  • Bob
  • Advanced Member
2010-02-04T10:21:55Z
The factory fitted Autopilot for the original rudder stock was the ST1000, with a D007 5" extension, the mounting cup was fitted directly into the portside combing, a reinforcing block was fitted to all 235s in this area , later 235s with the extended stock will also need a D030 89mm pedestal socket which is bolted on the top of the Portside combing bringing the autopilot to the correct height, the tiller pin was fitted on the top of the tiller 18" from the stock pivot point, and extra packing under the tiller extension clip to clear the pin.
James Hamilton
2010-02-04T13:23:31Z
Just to add to the chat, I fitted an St1000 , with extension, to the cockpit coaming, using a bracket under the tiller. This meant that I didn't need a pedestal, on the other hand, the clearance to the top of the engine is tight, and if someone sits on the tiller the engine cover gets scratched. However this is not a problem so far as working the autopilot goes.

Jim Hamilton

http://freespace.virgin....james.hamilton/forum.jpg 


Bob
  • Bob
  • Advanced Member
2010-02-08T16:09:46Z
Forgot to add that the ST1000 will need recalibrating to Portside operation, as Raymarine default is Starboard, its only a matter of holding down the two buttons for 10 secs, Please refer to Raymarine manual or website, (factory fitted ST1000 were recalibrated at installation.)

John Sorapure
2018-04-22T00:33:42Z
Hello All,

Coming to this post about 8 years late!

I want to fit a Raymarine ST2000 to my Parker 235 (2003), but wondered if anyone might have done this before and have any advice/photos before I start drilling holes?

Many thanks and all the best,

John

(Sandpiper)

ARRussell
2018-05-13T16:30:08Z
Hello John,

The ST2000 is identical in form to the ST1000, so fitting it is exactly as described by 'Bob' in this thread. The only difference I found was that the reinforcing block was missing from the coaming in my boat (hull 002) so I had to epoxy a plywood pad in place, but with a later boat you might be in luck with that.

One tip to note: in selecting a position for the cable socket, keep it as far from the engine as possible. I initially fitted it in the side of the cockpit seat, beside the engine, and I sometimes experienced electromagnetic interference from the engine at certain revs. I moved the socket and cable run to the coaming, beneath the autopilot's pivot pin, and that fixed it.

Best wishes,

Anthony


Anthony Russell

235/02 Sea Wyche